ds1200dc 1200 watt distributed power system front-end bulk power total output power: 180 to 264 vac: 1200 w 3.3 vdc or 5.0 vdc standby output telco input range: -40 to -72 vdc special features ? gr-1089-core issue 4 compliant ? 1u x 2u form factor ? 21.71 w / in 3 ? +12 vdc output ? +3.3 vdc standby (5 v standby option) ? no minimum load required ? hot plug operation ? n + 1 redundant ? internal oring fets ? active current sharing shares with ds1200 ac unit (10 - 100% load) ? built-in cooling fan (40 mm x 28 mm) ? i 2 c communication interface bus ? pmbus compliant ? eerpom for fru data ? red/green bi-color led status ? internal fan speed control ? fan fail tach output signal ? intel, ssi std. logic timing ? intel, ssi std. fru data format ? full digital control ? two year warranty ? nebs compliant safety ? ul/cul 60950 (ul recognized) ? nemko+ cb report en60950 ? en60950 ? ce mark ? china ccc electrical specifcations input input range -40 vdc to -72 vdc inrush current etsi en300 132-2 part 4.7 compliant effciency > 85% typical at high line 50% load conducted emi per gr-1089-core issue 4 radiated emi per gr-1089-core issue 4 leakage current 1.40 ma @ 240 vac hold up time 12 ms minimum output main dc voltage +12 v @ 100 a standby +3.3 vsb @ 6 a (5 v @ 4 a available) adjustment range 5% on +12 v only using i 2 c regulation +12 vdc; 5% +3.3 or 5.0 vsb 5% overcurrent +12 vdc; latches off if overcurrent lasts over 1 second, otherwise it is auto recovery (see table 1 next page) +3.3 vsb, 9 a max (hiccup mode) overvoltage +12 vdc; 13.2 - 14.4 vdc +3.3 vsb; 3.76 - 4.30 vdc undervoltage +12 vdc; 9 - 10.8 v (latch off) turn-on delay 2 second max, 5 - 50 ms, monotonic rise main output rise time 5 - 50 ms, monotonic rise data sheet power
logic control ps_seated (a4) ttl logic low if power supply is seated into system connector. this is a short pin. a logic high if the psu is removed pwr good (c3) active ttl high when output is within regulation limits. ac ok (b1) a low logic level if the input voltage is within allowable limits. a ttl logic high level, and a 5 ms early warning signal before 12.0 v dc output loss of regulation. ps_inhibit/ps_kill (b4) when left open power supply operation will be inhibited. when the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. ps on (a1) the output will be enabled when this signal is pulled low, below 0.8 v outputs disabled when pin is driven high or left open. environmental specifcations operating temperature -10 to 55 c storage temperature -40 to +85 c altitude, operating 13,000 feet electromagnetic susceptibility / input transients gr-1089-core issue 4 rohs & lead free compliant humidity 20 - 90% rh, non condensing shock and vibration specifcations complies with artesyn standard specifcations plus additional nebs requirement mtbf (demonstrated 500 k hrs at full load, 40 c ordering information model number* nominal output voltage set point set point tolerance total regulation current output ripple p/p overcurrent standby air flow min max ds1200dc-3 12.0 v 0.2% 0.5% 0 a 100 a 120 mv 118 a - 147.6 a* 3.3 v @ 6 a std ds1200dc-3-001 12.0 v 0.2% 0.5% 0 a 100 a 120 mv 118 a - 147.6 a* 3.3 v @ 6 a rev** ds1200dc-3-002 12.0 v 0.2% 0.5% 0 a 100 a 120 mv 118 a - 147.6 a* 5.0 v @ 4 a std DS1200DC-3-004 12.0 v 0.2% 0.5% 0 a 100 a 120 mv 118 a - 147.6 a* 5.0 v @ 4 a rev** * over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. ** derating may apply. ds1200dc data sheet
mechanical drawing conditon led status stand-by - on; main output - off; ac present blinking green stand-by - on; main output - on solid green main output ocp, uvp, ovp blinking amber fan_fault; otp; stand-by ocp/uvp amber f o r w ard ai rfl o w di re c tion mo del label (label te x t & chara c ter s a s o ri en ted) 275.5 279.4 1 7.02 0.8 81.3 0.8 39.9 0.5 68.8 6 9 ds1200dc data sheet
ds1200dc 30jul2015 mechanical specifcations power supply side 1. fci power blade 51721 series 51721-10002406aa 2. molex power connector sd-87667 series 87667-7002 mating connector (system side) 1. fci power blade 51741-10002406cc straight pins 2. fci power blade 51761-10002406aalf right angle pin assignments pin signal name pb1 main output return pb2 main output return pb3 main output return pb4 + main output pb5 + main output pb6 + main output a1 ps_on_ a2 main output remote sense return a3 spare a4 ps_seated (power supply seated) a5 standby a6 standby return b1 ac_ok (ac input present) b2 main output remote sense b3 main ouput current share b4 ps_inhibit / ps_kill b5 standby b6 standby return c1 adc (i 2 c data signal) c2 scl (i 2 c clock signal) c3 power good c4 spare c5 standby c6 standby return d1 a0 (i 2 c address bit 0 signal) d2 a1 (i 2 c address bit 1 signal) d3 s_int (alarm) d4 standyby rmt sense d5 standby d6 standby return male connector as viewed from the rear of the supply: d1 d2 d3 d4 d5 d6 pb1 pb2 pb3 pb4 pb5 pb6 c1 c2 c3 c4 c5 c6 b1 b2 b3 b4 b5 b6 a1 a2 a3 a4 a5 a6 dc output connector pinout assignment ds1200dc data sheet for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com www.artesyn.com worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 while every precaution has been taken to ensure accuracy and completeness in this literature, artesyn embedded technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2015 artesyn embedded technologies, inc.
|
